API 5L Heavy Wall Seamless Carbon Pipe Supplier, Exporter

API 5L Heavy Wall Seamless Carbon Pipe, Heavy Wall Seamless Carbon Pipe, Heavy Wall Seamless Carbon Pipe, Carbon Steel API 5L Heavy Wall Seamless Pipe Suppliers in Mumbai, India.

Leoscor Alloys is one of the most reputed Manufacturer and Exporter of API 5L Heavy Wall Seamless Carbon Pipe / Seamless Pipe traders in the Indian market. We offer these API 5L Heavy Wall Seamless Pipes at market leading prices. We also offer these API 5L Heavy Wall Seamless Carbon Pipes in different customized sizes and shapes as per customer requirements. Meanwhile, Grade designations of API 5L Line pipe produced by Prosaic Steel and Alloys come from the American Petroleum Institute (API) Spec 5L Specification for line pipe.

Heavy Wall Seamless Carbon Pipe Exporter , API 5L Heavy Wall Seamless Pipe Dealer, Heavy Wall Seamless CS Pipe, CS API 5L Heavy Wall Pipe Manufacturer in India.

We specialise in API 5L Carbon Steel Pipes / Black Steel Pipe Exporting in Turkey, Egypt, Singapore, Malaysia, Indonesia, Jordan, South Africa, Oman, Qatar, Italy.

API 5L Heavy Wall Seamless Carbon Pipe Specifications

Product	:	API 5L Heavy Wall Seamless Pipe
Standard	:	API 5L
Length	:	5.8m,6m-11.85m,12m or any other length
OD	:	1/8"-36" WT: 1-50mm
Other	:	Black Painting,Caps,BE,PE,Marking and so on

API 5L Heavy Wall Seamless Carbon Pipe

Heavy Wall Seamless Carbon Pipe

Delivery Condition

PSL	Delivery Condition	Pipe grade
PSL 1	As-rolled, normalized, normalizing formed	A
	As-rolled, normalizing rolled, thermomechanical rolled, thermo-mechanical formed, normalizing formed, normalized, normalized and tempered or if agreed Q&T SMLS only	B
	As-rolled, normalizing rolled, thermomechanical rolled, thermo-mechanical formed, normalizing formed, normalized, normalized and tempered	X42, X46, X52, X56, X60, X65, X70
PSL 2	As-rolled	BR, X42R
	Normalizing rolled, normalizing formed, normalized or normalized and tempered	BN, X42N, X46N, X52N, X56N, X60N
	Quenched and tempered	BQ, X42Q, X46Q, X56Q, X60Q, X65Q, X70Q, X80Q, X90Q, X100Q
	Thermomechanical rolled or thermomechanical formed	BM, X42M, X46M, X56M, X60M, X65M, X70M, X80M
	Thermomechanical rolled	X90M, X100M, X120M
	The suffice (R, N, Q or M) for PSL2 grades, belongs to the steel grade

Chemical Composition for PSL 1 pipe with t ≤ 0.984”

Steel Grade	Mass fraction, % based on heat and product analyses a,g
Steel Grade	C max b	Mn max b	P max	S max	V max	Nb max	Ti max
Seamless Pipe
A	0.22	0.90	0.30	0.30	-	-	-
B	0.28	1.20	0.30	0.30	c,d	c,d	d
X42	0.28	1.30	0.30	0.30	d	d	d
X46	0.28	1.40	0.30	0.30	d	d	d
X52	0.28	1.40	0.30	0.30	d	d	d
X56	0.28	1.40	0.30	0.30	d	d	d
X60	0.28 e	1.40 e	0.30	0.30	f	f	f
X65	0.28 e	1.40 e	0.30	0.30	f	f	f
X70	0.28 e	1.40 e	0.30	0.30	f	f	f
Welded Pipe
A	0.22	0.90	0.30	0.30	-	-	-
B	0.26	1.2	0.30	0.30	c,d	c,d	d
X42	0.26	1.3	0.30	0.30	d	d	d
X46	0.26	1.4	0.30	0.30	d	d	d
X52	0.26	1.4	0.30	0.30	d	d	d
X56	0.26	1.4	0.30	0.30	d	d	d
X60	0.26 e	1.40 e	0.30	0.30	f	f	f
X65	0.26 e	1.45 e	0.30	0.30	f	f	f
X70	0.26e	1.65 e	0.30	0.30	f	f	f
Cu ≤ = 0.50% Ni; ≤ 0.50%; Cr ≤ 0.50%; and Mo ≤ 0.15% For each reduction of 0.01% below the specified max. concentration for carbon, and increase of 0.05% above the specified max. concentration for Mn is permissible, up to a max. of 1.65% for grades ≥ B, but ≤ = X52; up to a max. of 1.75% for grades > X52, but < X70; and up to a maximum of 2.00% for X70. Unless otherwise agreed NB + V ≤ 0.06% Nb + V + TI ≤ 0.15% Unless otherwise agreed. Unless otherwise agreed, NB + V = Ti ≤ 0.15% No deliberate addition of B is permitted and the residual B ≤ 0.001%

Chemical Composition for PSL 2 pipe with t ≤ 0.984”

API 5L X70 PSL1 and PSL2 Pipe Yield Strength & Tensile Strength

Steel Grade	Mass fraction, % based on heat and product analyses																		Carbon Equiv a
	C max b		Si max		Mn max b		P max		S max		V max		Nb max		Ti max		Other		CE IIW max		CE Pcm max
Seamless and Welded Pipe
BR	0.24		0.40		1.20		0.025		0.015		c		c		0.04		e,l		.043		0.25
X42R	0.24		0.40		1.20		0.025		0.015		0.06		0.05		0.04		e,l		.043		0.25
BN	0.24		0.40		1.20		0.025		0.015		c		c		0.04		e,l		.043		0.25
X42N	0.24		0.40		1.20		0.025		0.015		0.06		0.05		0.04		e,l		.043		0.25
X46N	0.24		0.40		1.40		0.025		0.015		0.07		0.05		0.04		d,e,l		.043		0.25
X52N	0.24		0.45		1.40		0.025		0.015		0.10		0.05		0.04		d,e,l		.043		0.25
X56N	0.24		0.45		1.40		0.025		0.015		0.10f		0.05		0.04		d,e,l		.043		0.25
X60N	0.24f		0.45f		1.40f		0.025		0.015		0.10f		0.05f		0.04f		g,h,l		As agreed
BQ	0.18		0.45		1.40		0.025		0.015		0.05		0.05		0.04		e,l		.043		0.25
X42Q	0.18		0.45		1.40		0.025		0.015		0.05		0.05		0.04		e,l		.043		0.25
X46Q	0.18		0.45		1.40		0.025		0.015		0.05		0.05		0.04		e,l		.043		0.25
X52Q	0.18		0.45		1.50		0.025		0.015		0.05		0.05		0.04		e,l		.043		0.25
X56Q	0.18		0.45f		1.50		0.025		0.015		0.07		0.05		0.04		e,l		.043		0.25
X60Q	0.18f		0.45f		1.70f		0.025		0.015		g		g		g		h,l		.043		0.25
X65Q	0.18f		0.45f		1.70f		0.025		0.015		g		g		g		h,l		.043		0.25
X70Q	0.18f		0.45f		1.80f		0.025		0.015		g		g		g		h,l		.043		0.25
X80Q	0.18f		0.45f		1.90f		0.025		0.015		g		g		g		i,j		As agreed
X90Q	0.16f		0.45f		1.90		0.020		0.010		g		g		g		j,k		As agreed
X100Q	0.16f		0.45f		1.90		0.020		0.010		g		g		g		j,k		As agreed
Welded Pipe
BM		0.22		0.45		1.20		0.025		0.015		0.05		0.05		0.04		e,l		.043	0.25
X42M		0.22		0.45		1.30		0.025		0.015		0.05		0.05		0.04		e,l		.043	0.25
X46M		0.22		0.45		1.30		0.025		0.015		0.05		0.05		0.04		e,l		.043	0.25
X52M		0.22		0.45		1.40		0.025		0.015		d		d		d		e,l		.043	0.25
X56M		0.22		0.45f		1.40		0.025		0.015		d		d		d		e,l		.043	0.25
X60M		0.12f		0.45f		1.60f		0.025		0.015		g		g		g		h,l		.043	0.25
X65M		0.12f		0.45f		1.60f		0.025		0.015		g		g		g		h,l		.043	0.25
X70M		0.12f		0.45f		1.70f		0.025		0.015		g		g		g		h,l		.043	0.25
X80M		0.12f		0.45f		1.85f		0.025		0.015		g		g		g		i,j		.043f	0.25
X90M		0.10		0.55f		2.10f		0.020		0.010		g		g		g		i,j		-	0.25
X100M		0.10		0.55f		2.10f		0.020		0.010		g		g		g		i,j		-	0.25
SMLS t>0.787”, CE limits shall be as agreed. The CEIIW limits applied fi C > 0.12% and the CEPcm limits apply if C ≤ 0.12% For each reduction of 0.01% below the specified max. concentration for carbon, and increase of 0.05% above the specified max. concentration for Mn is permissible, up to a max. of 1.65% for grades ≥ B, but ≤ = X52; up to a max. of 1.75% for grades > X52, but < X70; and up to a maximum of 2.00% for X70. Unless otherwise agreed Nb = V ≤ 0.06% Nb = V = Ti ≤ 0.15% Unless otherwise agreed, Cu ≤ 0.50%; Ni ≤ 0.30% Cr ≤ 0.30% and Mo ≤ 0.15% Unless otherwise agreed Unless otherwise agreed, Nb + V + Ti ≤ 0.15% Unless otherwise agreed, Cu ≤ 0.50% Ni ≤ 0.50% Cr ≤ 0.50% and MO ≤ 0.50% Unless otherwise agreed, Cu ≤ 0.50% Ni ≤ 1.00% Cr ≤ 0.50% and MO ≤ 0.50% B ≤ 0.004% Unless otherwise agreed, Cu ≤ 0.50% Ni ≤ 1.00% Cr ≤ 0.55% and MO ≤ 0.80% For all PSL 2 pipe grades except those grades with footnotes j noted, the following applies. Unless otherwise agreed no intentional addition of B is permitted and residual B ≤ 0.001% .

Mechanical properties – PSL1 and PSL2

Pipe Grade	Tensile Properties - Pipe Body of SMLS and Welded Pipes PSL 1			Seam of Welded Pipe
Pipe Grade	Yield Strength a Rt0,5 PSI Min	Tensile Strength a Rm PSI Min	Elongation (in 2in Af % min)	Tensile Strength b Rm PSI Min
A	30,500	48,600	c	48,600
B	35,500	60,200	c	60,200
X42	42,100	60,200	c	60,200
X46	46,400	63,100	c	63,100
X52	52,200	66,700	c	66,700
X56	56,600	71,100	c	71,100
X60	60,200	75,400	c	75,400
X65	65,300	77,500	c	77,500
X70	70,300	82,700	c	82,700
a. For intermediate grade, the difference between the specified minimum tensile strength and the specified minimum yield for the pipe body shall be as given for the next higher grade. b. For the intermediate grades, the specified minimum tensile strength for the weld seam shall be the same as determined for the body using foot note a. c. The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be determined using the following equation: Where C is 1 940 for calculation using Si units and 625 000 for calculation using USC units Axc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches) , as follows For circular cross-section test pieces, 130mm2 (0.20 in2) for 12.7 mm (0.500 in) and 8.9 mm (.350 in) diameter test pieces; and 65 mm2 (0.10 in2) for 6.4 mm (0.250in) diameter test pieces. For full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2) For strip test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2) U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch)

Pipe Grade	Tensile Properties - Pipe Body of SMLS and Welded Pipes PSL 2						Seam of Welded Pipe
	Yield Strength a Rt0,5 PSI Min		Tensile Strength a Rm PSI Min		Ratio a,c R10,5IRm	Elongation (in 2in) Af %	Tensile Strength d Rm (psi)
	Minimum	Maximum	Minimum	Maximum	Maximum	Minimum	Minimum
BR, BN,BQ,BM	35,500	65,300	60,200	95,000	0.93	f	60,200
X42,X42R,X2Q,X42M	42,100	71,800	60,200	95,000	0.93	f	60,200
X46N,X46Q,X46M	46,400	76,100	63,100	95,000	0.93	f	63,100
X52N,X52Q,X52M	52,200	76,900	66,700	110,200	0.93	f	66,700
X56N,X56Q,X56M	56,600	79,000	71,100	110,200	0.93	f	71,100
X60N,X60Q,S60M	60,200	81,900	75,400	110,200	0.93	f	75,400
X65Q,X65M	65,300	87,000	77,600	110,200	0.93	f	76,600
X70Q,X65M	70,300	92,100	82,700	110,200	0.93	f	82,700
X80Q,X80M	80,.500	102,300	90,600	119,700	0.93	f	90,600
a. For intermediate grade, refer to the full API5L specification. b. for grades > X90 refer to the full API5L specification. c. This limit applies for pies with D> 12.750 in d. For intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using foot a. e. for pipe requiring longitudinal testing, the maximum yield strength shall be ≤ 71,800 psi f. The specified minimum elongation, Af, expressed in percent and rounded to the nearest percent, shall be determined using the following equation: Where C is 1 940 for calculation using Si units and 625 000 for calculation using USC units Axc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches) , as follows For circular cross-section test pieces, 130mm2 (0.20 in2) for 12.7 mm (0.500 in) and 8.9 mm (.350 in) diameter test pieces; and 65 mm2 (0.10 in2) for 6.4 mm (0.250in) diameter test pieces. For full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2) For strip test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.10in2) U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch g. Lower values fo R10,5IRm may be specified by agreement h. for grades > x90 refer to the full API5L specification.

API 5L Pipe Outside Diameter Tolerance

Specified Outside Diameter D (in)	Diameter Tolerance, inches d				Out-of-Roundness Tolerance in
	Pipe except the end a		Pipe end a,b,c		Pipe except the End a	Pipe End a,b,c
	SMLS Pipe	Welded Pipe	SMLS Pipe	Welded Pipe
< 2.375	-0.031 to + 0.016		- 0.031 to + 0.016		0.048	0.036
≥2.375 to 6.625	+/- 0.0075D		- 0.016 to + 0.063		0.020D for By agreement for	0.015D for By agreement for
>6.625 to 24.000	+/- 0.0075D	+/- 0.0075D, but max of 0.125	+/- 0.005D, but max of 0.063		0.020D	0.015D
>24 to 56	+/- 0.01D	+/- 0.005D but max of 0.160	+/- 0.079	+/- 0.063	0.015D for but max of 0.060 For By agreement for	0.01D for but max of 0.500 For By agreement for
>56	As agreed
The pipe end includes a length of 4 in ate each of the pipe extremities For SMLS pipe the tolerance apply for t≤0.984in and the tolerances for the thicker pipe shall be as agreed For expanded pipe with D≥8.625in and for non-expanded pipe, the diameter tolerance and the out-of-roundness tolerance may be determined using the calculated inside diameter or measured inside diameter rather than the specified OD. For determining compliance to diameter tolerance, the pipe diameter is defined as the circumference of the pipe in any circumferential plane divide by Pi.

API 5L Pipe Wall Thickness Tolerance (WT)

Wall thickness t inches	Tolerances a inches
SMLS pipe b
≤ 0.157	+ 0.024 / - 0.020
0.157 to < 0.948	+ 0.150t / - 0.125t
≥ 0.984	+ 0.146 or + 0.1t, whichever is the greater - 0.120 or – 0.1t, whichever is the greater
Welded pipe c,d
≤ 0.197	+/- 0.020
> 0.197 to < 0.591	+/- 0.1t
≥ 0.591	+/- 0.060
If the purchase order specifies a minus tolerance for wall thickness smaller than the applicable value given in this table, the plus tolerance for wall thickness shall be increased by an amount sufficient to maintain the applicable tolerance range. For pipe with D≥ 14.000 in and t≥0.984in, the wall thickness tolerance locally may exceed the plus tolerance for wall thickness by an additional 0.05t provided that the plus tolerance for mass is not exceeded. The plus tolerance for wall thickens does not apply to the weld area See the full API5L spec for full details

Permissible Variations for Seamless and Welded API 5L Steel Pipe

	Grade A, B, A25	X42 through X80
NPS 2-1/2 and smaller --Seamless and Welded, %	+20 -- 12.5	+15 -- 12.5
NPS 3 --Seamless and Welded, %	+18 -- 12.5	+15 -- 12.5
NPS 4 through 18 --Seamless and Welded, %	+15 -- 12.5	+15 -- 12.5
NPS 20 and larger -- Welded, %	+17.5 -- 10.0	+19.5 -- 8.0
NPS 20 and larger -- Seamless, %	+15.0 -- 12.5	+17.5 -- 10.0

Price List of API 5L Heavy Wall Seamless Carbon Pipe

Price of Carbon Steel API 5L Heavy Wall Seamless Pipes : US $630-1100 / Ton ( FOB Price)

Price of API 5L Heavy Wall Seamless Carbon Pipes : US $630-1100 / Ton ( FOB Price)

API 5L Heavy Wall Seamless Carbon Pipes Available Stock at Leoscor Alloys & Steel Inc.

We have Largest inventory of API 5L Heavy Wall Seamless Carbon Pipe. Carbon Steel API 5L API 5L Heavy Wall Seamless Carbon Pipe, API 5L API 5L Heavy Wall Seamless Carbon Pipes Suppliers, API 5L API 5L Heavy Wall Seamless Carbon Pipe Exporter, API 5L API 5L Heavy Wall Seamless Carbon Steel Pipe, API 5L API 5L Heavy Wall Seamless Carbon Pipe Dealer, API 5L API 5L Heavy Wall Seamless Carbon Pipe Suppliers in Mumbai, India, API 5L Heavy Wall Seamless Carbon Pipe Stockholder, Heavy Wall Seamless Carbon Pipe Distributors, API 5L API 5L Heavy Wall Seamless Pipe, Carbon Steel API 5L Heavy Wall Seamless Pipe Suppliers, API 5L Heavy Wall Seamless Carbon Pipes, Heavy Wall Seamless Carbon Pipe Stockist, API 5L Heavy Wall Seamless Carbon Pipe, API 5L Heavy Wall Seamless Carbon Pipe, Carbon Steel API 5L Heavy Wall Seamless Pipe Suppliers, We are india's most trusted Manufacturer, Suppliers & Exporter of Carbon Steel API 5L Heavy Wall Seamless Pipe, API 5L Heavy Wall Seamless Carbon Pipe are Available in Different Dimensions and Specifications in INDIA.

Carbon Steel API 5L Heavy Wall Seamless Carbon Pipe Application Industry

Gas Processing Industries

Petrochemical Industries

Power Generation Industries

Food Processing Industries

Chemical Industries

Oil & Gas Industries

Fertilizers Industries

Sugar Industries